Author: Mary Dufresne

Water Heater Repair – What You Need to Know

Most homeowners take their water heaters for granted until they break down. Then, showers and laundry become unheard of, dishes go undone, and a whole household can feel like it has come to a halt.

Water Heater Repair

Some water heater problems require the help of a professional. These issues can include a lack of hot water, leaking, faulty pilot lights, or strange noises. Contact Water Heater Repair Spring TX for professional help.

Water heaters play a very important role in the daily lives of many families. They are used to heat homes, wash clothes, cook meals, and provide a constant supply of hot water for showers. When they break down, it can be a major inconvenience and cause serious damage to home plumbing and piping. It’s important to catch problems early, like a leak or no hot water, so they can be repaired before too much damage is done.

An electric water heater that produces no hot water might have a tripped high temperature limit switch, a broken heating element, or both. Start by shutting off power to the heater at your home’s service panel. Disconnect the upper and lower heating elements and remove their covers. With the power still off, use a multi-meter to check the heating elements for continuity (they should read about 13 ohms of resistance). If both are broken, you will need to replace them. Our Replacing a Heating Element video gives step-by-step instructions.

A gas-powered water heater has a different type of thermostat that may require more troubleshooting and repair. If yours does not produce a pilot flame, you will need to use a long lighter to reach into the access cover and light it manually. After a minute, the pilot should glow steady, and you can turn the gas valve back on to activate it.

Another possible issue with a gas-powered heater is that the thermocouple has gone bad. A professional can replace it for you if needed. Finally, a noisy water heater that is producing popping or crackling sounds could indicate mineral deposits that need to be removed. This is usually an easy problem to fix and does not require a professional. Water that smells rotten or metallic could indicate that the hot water tank is leaking and needs to be replaced. If you notice a large area of water around the heater, it is time to call in a professional. Water leaks can ruin flooring and cause severe property damage. Leaks in the basement are particularly dangerous and should always be addressed immediately.


Most people don’t think much about their water heater, as long as it works. When it breaks down, though, we suddenly realize just how important this household appliance is. Without a functioning water heater, no one can take hot showers, wash dishes, or do laundry. That’s why it’s critical to repair your water heater as soon as you notice an issue.

If you don’t have any hot water, first check to make sure the circuit breaker or high-temperature cutoff isn’t tripped. Pressing the reset button on these switches will restore power to your water heater and hopefully get it up and running again. If you do this and your heater still doesn’t produce hot water, the problem could be with the upper or lower heating element.

A bad heating element is a common problem with electric water heaters, as they can burn out and short circuit. If you notice that your heater is tripping the circuit breakers, it’s probably time to call a professional plumber to replace the heating elements.

In addition to being expensive, it’s also inconvenient to be without hot water for an extended period of time. Luckily, a professional plumber will be able to diagnose the problem and provide an efficient solution.

Occasionally, sediment can accumulate inside the bottom of your tank. Over time, this will create a buildup that may affect the performance of your heater. To avoid this, it’s recommended that you drain and flush your water heater at least once per year. If you aren’t comfortable doing this yourself, a local plumber can usually do it for an hourly rate.

Another part of your water heater that can wear out is the dip tube. This tube transfers cool water from the top of your tank to the bottom so it can be reheated by the heating element. If this tube goes bad, you’ll experience a loss of efficiency, as cold water will mix with the hot water and reduce its temperature.

It’s also possible that you have a problem with the thermocouple or gas control valve, both of which are fairly simple to fix. These small parts can go bad due to old age or excessive sediment. The thermocouple is a safety device that detects whether the pilot light is lit or not, and the gas control valve controls the flow of gas to the burner.

Dip Tube

The dip tube is responsible for dropping cold water down to the bottom of the tank to mix with the hot water before it exits to your faucets. If you notice that your showers start out hot but quickly turn lukewarm, or you run out of hot water in the middle of a shower, this is likely because the dip tube has broken and isn’t dumping cold water to the bottom of the tank.

The good news is that fixing this problem is relatively simple and involves replacing the dip tube with a new one. First, make sure that the power to the water heater is turned off at the circuit breaker for safety reasons. Then, drain several gallons of water from the tank using your garden hose or the hot water drain valve.

Once the water is drained, locate the dip tube on the top of the tank and disconnect it by loosening the inlet connection nipple with a pipe wrench. Next, remove the old dip tube and replace it with a new one. When selecting a replacement, opt for one made from heat-resistant plastic rather than metal to prevent damaging the sacrificial anode that is also installed in the tank. Metals react with the anode and can hasten its consumption, which can lead to rust-related tank leaks.

When installing the new dip tube, apply a small amount of plumber’s tape to the end of the plastic tube to seal off any potential leaks. Then, insert the new tube into the inlet and push it all the way down into the tank to ensure that it reaches the water at the bottom of the tank. Finally, screw the inlet nipple and connector back onto the tank, reconnect the cold water pipe, and restore power to the water heater.

If you follow these steps, your water heater should return to full functionality and you’ll be enjoying piping hot showers again before you know it! However, if your water heater continues to malfunction, it’s best to call in the professionals at Mr. Rooter to take a look at your unit and perform a thorough inspection.

Pressure Valve

The pressure valve is a vital safety feature of the water heater. It is designed to discharge excess hot water and reduce the risk of a catastrophic explosion of the tank. It works by using a mechanical spring to force open the metal valve lever, which discharges water into the discharge tube. The discharge tube is designed to extend about six inches above the floor of the water heater.

Whenever the pressure of a water heater rises, the pressure valve opens. Ideally, the water flows freely through the valve and is not restricted. But if the pressure is excessive, the valve will begin to crack. Eventually, the crack will increase in size until it is large enough to open the valve and relieve the pressure.

To prevent the risk of explosion, most states and cities require that the pressure relief valve be capable of releasing the excess heat and water in a controlled way. This is why most homeowners in Chicago test the pressure valve when they flush and drain their water heater twice a year.

When the pressure valve is functioning properly, water is discharged through the valve when the hot water temperature in the water heater reaches the set point. The water then flows through the discharge pipe and down the drain, thereby lowering the water pressure in the pipes and preventing the pressure from rising above the valve setting.

The most common cause of a malfunctioning water heater pressure valve is a faulty body or seal. The seal material must be compatible with the fluid to be pumped and must be able to function in the expected operating temperature range. Buna-N is a common seal material, although some manufacturers offer alternative materials.

Another possible reason for a faulty water heater pressure valve is a physical restriction in the water heater or plumbing system. If the water heater has not been installed correctly, or if the pipes connecting it to the water heater are too small or clogged with mineral deposits, pressure could build up. This may eventually cause the relief valve to crack open and leak water.

The Profession of a Plumber

A plumber is a skilled tradesman who installs and repairs pipes. This profession requires a solid knowledge of chemistry and physics in order to troubleshoot problems and install the proper piping systems. Plumbers must have good communication skills and the physical strength to handle strenuous tasks. They should be able to lift heavy tools and equipment. Job prospects for plumbers are promising. According to the U.S. Bureau of Labor Statistics, job growth for plumbers is predicted to be 15% between 2016 and 2026. The growth in the job market is based on the overall state of the economy and will continue to be dependent on it.

The tasks a plumber performs on a daily basis will vary depending on what kind of plumbing he or she works on. A plumber working in a residential home will most likely be dealing with a clogged drain or leaking pipe. A plumber working in a commercial building may be installing a large-scale plumbing system. Regardless of the type of plumbing that he or she works on, he or she must remain alert to any potential emergencies and be able to solve them quickly and efficiently.

There are two main routes to becoming a plumber. One is through an apprenticeship program, which may require two to five years to complete. The program provides hands-on training and an academic foundation. Some schools offer an apprenticeship program for up to five years. In addition to coursework, apprentices usually undergo two years of hands-on training in plumbing companies, including repairing and installing plumbing systems. This training is usually supervised by a master plumber. To be a plumber, you should have a license in your state.

If you are looking for a plumber, ask friends or family members for referrals. Alternatively, check online reviews for plumbers to get feedback from others. Read positive and negative reviews so you can decide whether to hire someone or not. In addition to recommendations, make sure the plumber is licensed and insured to protect yourself. You can also schedule an appointment with the plumber to get your pipes repaired. Remember to pay the plumber. If he is unable to come to your home, don’t be afraid to pay him extra.

Most plumbers work forty hours a week. However, this may increase to sixty hours per week during peak work periods. Depending on the region, job, and sector, you can expect to work even more hours. Overtime is common. A plumber’s job also requires constant standing and lifting heavy materials. You should be prepared to travel a lot. If you are passionate about plumbing, it could be a rewarding career. The salary and benefits are substantial.

Obtaining an apprenticeship in plumbing is the first step toward becoming a professional plumber. It requires at least five GCSEs in English and maths. You can also gain experience by working under a licensed plumber. It’s important to note that there are different levels of certification for plumbing in Canada. If you have a Red Seal, you can work anywhere in Canada. But it’s not necessary to obtain this certification if you don’t have experience.

A master plumber, also known as a master plumber, has advanced training and experience. These plumbers work on larger construction projects and must meet strict building codes. They must also stay within budgets. The Bureau of Labor Statistics predicts a rise in demand for plumbing masters in the next decade. This is because the number of new buildings and stricter water efficiency regulations will increase the need for these plumbers. The highest paid plumbing jobs are master plumbers.

Choosing the right certification for plumbing can greatly increase your prospects of securing a good job. There are many different plumbing certifications available, which allow you to specialize and become a master plumber. You can choose to become a journeyman plumber, or you can choose to specialize in any of these specializations. The skills you gain through your apprenticeship will allow you to choose a specialization in plumbing. It’s possible to become a master plumber through an apprenticeship, as long as you have the right education.

In New York City, a master plumber must hold a license from the Department of Buildings. A master plumber may supervise plumbers working under his supervision. However, this license is not granted to those who have less experience in plumbing. However, master plumbers must have completed a two-year apprenticeship as a journeyman plumber in New York City. Once they have gained this license, they can continue to practice plumbing as a master plumber. The average salary of a plumber in the city is $58,360.